RCHourglass Zeitnahme

Payalneg + alter decoder ging in der Halle gut

mit Schleifenbreite spielen, was ist die max. breite?

Decoder Gehäuse besser an GND anbinden

2. Schnittstelle aktivieren?

Werkstatt PC hat mehr Hits als Laptop (Messung nochmal wiederholen)

Decoder Lochraster + Cano amplifier =⇒ 31,2 Hits

Decoder Lochraster + Payalneg =⇒ 65,2 Hits

Decoder PCB + Payalneg =⇒ 50 Hits

Payalneg hat viel mehr Amplitude, ist aber unsymetrisch

https://github.com/mv4wd/RCHourglass

https://www.rctech.net/forum/radio-electronics/1002584-rchourglass-diy-lap-timing-aka-cano-revised.html

https://www.rctech.net/forum/radio-electronics/688396-transponder-design.html

http://rc-auto.ru/forum/index.php?s=2874794e18a6632e9c873096d90c13bb&showtopic=20470&st=40

Wieviel der Bits werden für die ID verwendet? ⇒ alle

Niedrige Qualität kann schon plausibel sein. Jede 2. Message ist RC4, von 4 RC3 Message ist eine eine Status Message.

Schaltung relativ unabhängig von Schleifenlänge, 3×0,3 m keine Jumper. Wenn kleiner dann erst Jumper verwenden

Oder mit breite der schleife spielen

• Induktivität der roten Schleife 9,774µH
• Induktivität der grünen Schleife 8,153µH

180° PSK

99bits in einer Message entspricht ungefähr den 24 Hex Werten in Monitor mode

200ns Periode

FC0A - RC4

F916 - RC3 oder z.B. 7916 erstes Bit wird nicht bewertet

Preamble 16bit 0XFFFF

ID 24bit 0XFFFFFF

115200 Baud

Transpondernummer ms viertel (hex)

Decoder protocols

RCHourglass can use different protocols to send passages information to the lap timing software:

• <font 12pt/-apple-system;;inherit;;inherit>Cano/Cano classic protocol derived from original Cano decoder</font> * <font 12pt/-apple-system;;inherit;;inherit>RCHourglass protocol, similar to Cano protocol, but passage informations have some extra info like number of hits/quality/voltage/temp</font> * <font 12pt/-apple-system;;inherit;;inherit>AMBRc serial protocol</font> * <font 12pt/-apple-system;;inherit;;inherit>Tranx serial protocol</font>

<font 10pt/-apple-system;;inherit;;inherit><font 12pt„>nnnnnn is an ASCII HEX string that represents the transponder number.</font> * <font 12pt/-apple-system;;inherit;;inherit>tttttttt part is an 8 character ASCII string representing the passage time in quarters of milliseconds from decoder startup.</font>

Example record

23E35500075A06

Transponder: 0x23E355= 2351957

Time in quarter of ms = 0x00075A06= 120.449 seconds

The RCHourglass protocol passage record is 25 characters long in the format nnnnnntttttttt-idhhqqvvtm

The first 14 characters are the same as Cano protocol.

• <font 12pt/-apple-system;;inherit;;inherit>id the decoder ID (part of the decoder setup)</font> * <font 12pt/-apple-system;;inherit;;inherit>hh the number of hits received from the transponder</font> * <font 12pt/-apple-system;;inherit;;inherit>qq quality indicator of read (0-100%).</font> * <font 12pt/-apple-system;;inherit;;inherit>vv voltage in 1/10 of V</font> * <font 12pt/-apple-system;;inherit;;inherit>tt temperature ( 100 °C offset)</font>

All numbers a ASCII Hex.

Example record

23E35500075A06-01152A3787

Transponder: 0x23E355 = 2351957

Time in quarter of ms = 0x00075A06 = 120.449 seconds

Decoder ID : 0x01

Hits : 0x15 = 21 hits

Quality : 0x2A = 52%

Voltage: 0x37 = 5.5V

Temperature: 0x87 - 100 = 35°C

NOTE Temperature and voltage info are read only from RCHouglass transponder firmware to be developed. Values are 0 for measure not available.

Note that any derivative work MUST respond to LICENSE command with the same licensing terms.

NOTE for AMB emulation this is an emulationfor AMBRC protocol. Passage records with number of hits and low voltage indicator are supported. This is to use the decoder with lap timing softwares that do not support CANO protocol. Low voltage bit is rised with a voltage threshold set in the decoder configuration

Example:

GET TIME

Response

SUCCESS GET TIME 00075A06

Current time in quarter of ms = 0x00075A06 = 120.449 seconds

To set the same time:

SET TIME 75A06

<font 10pt/-apple-systemrgb(36, 41, 46) font-family: -apple-system; font-size: 10pt;;;inherit>Transponder management</font>/-apple-system;;inherit;;inherit>tx number, for example REGISTER 3462137 The decoder will start learn and return success or failure. In case of failure, reposition the car and/or check correct loop connection. In case of success, the 12 most important 'packets' of the transponder are reported, with the number of hits for each one. A minimum number of hits above 30, with the maximum above 100 is a very good target. The registration can use a nickname for the transponder, like REGISTER 3462137 MARCO. The nick name will appear in the list of registered transponders. The last option is to make a transponder 'important' that is it's never going to be 'kicked out' of the memory if the limit of 40 transponders is reached. Important transponders can be only deleted manually. When the memory is full, the oldest non important transponders are deleted to make room for the last registered one. For example, to register yours as an important transponder, write REGISTER I 3462137 MINE where MINE is the optional nickname. Learn process can be interrupted with the ABORT command, but it will timeout if no transponder is detected. The LIST command will show the registered transponders. The DELETE tx number, for example DELETE 3462137, will remove a transponder registration from the decoder memory. The INFO tx number, will show registration informations for a specific transponder. This commands are made to backup on the computer registration informations. Flashing a new firmware will EREASE the registrations done. </font>

NOTE a 50 ms blank time is always inserted in case of multiple close car passages.

DETECT response is multi line. The last line is SUCCESS PIC MODEL NNNN where *<font inherit„>NNNNis Hex part number ID. A value of 3066 sould be reported for PIC 16F18313.

Eingefügt aus <https://github.com/mv4wd/RCHourglass/wiki/CommandReference>

180° PSK

99bits in einer Message entspricht ungefähr den 24 Hex Werten in Monitor mode

200ns Periode

FC0A - RC4

F916 - RC3 oder z.B. 7916 erstes Bit wird nicht bewertet

Preamble 16bit 0XFFFF

ID 24bit 0XFFFFFF

115200 Baud

Transpondernummer + ms viertel (hex)

Decoder protocols

RCHourglass can use different protocols to send passages information to the lap timing software:

• <font 12pt/-apple-system;;inherit;;inherit>Cano/Cano classic protocol derived from original Cano decoder</font> * <font 12pt/-apple-system;;inherit;;inherit>RCHourglass protocol, similar to Cano protocol, but passage informations have some extra info like number of hits/quality/voltage/temp</font> * <font 12pt/-apple-system;;inherit;;inherit>AMBRc serial protocol</font> * <font 12pt/-apple-system;;inherit;;inherit>Tranx serial protocol</font>

<font 10pt/-apple-system;;inherit;;inherit><font 12pt“>nnnnnn is an ASCII HEX string that represents the transponder number.</font> * <font 12pt/-apple-system;;inherit;;inherit>tttttttt part is an 8 character ASCII string representing the passage time in quarters of milliseconds from decoder startup.</font>

Example record

23E35500075A06

Transponder: 0x23E355= 2351957

Time in quarter of ms = 0x00075A06= 120.449 seconds

The RCHourglass protocol passage record is 25 characters long in the format nnnnnntttttttt-idhhqqvvtm

The first 14 characters are the same as Cano protocol.

• <font 12pt/-apple-system;;inherit;;inherit>id the decoder ID (part of the decoder setup)</font> * <font 12pt/-apple-system;;inherit;;inherit>hh the number of hits received from the transponder</font> * <font 12pt/-apple-system;;inherit;;inherit>qq quality indicator of read (0-100%).</font> * <font 12pt/-apple-system;;inherit;;inherit>vv voltage in 1/10 of V</font> * <font 12pt/-apple-system;;inherit;;inherit>tt temperature (+100 °C offset)</font>

All numbers a ASCII Hex.

Example record

23E35500075A06-01152A3787

Transponder: 0x23E355 = 2351957

Time in quarter of ms = 0x00075A06 = 120.449 seconds

Decoder ID : 0x01

Hits : 0x15 = 21 hits

Quality : 0x2A = 52%

Voltage: 0x37 = 5.5V

Temperature: 0x87 - 100 = 35°C

NOTE Temperature and voltage info are read only from RCHouglass transponder firmware to be developed. Values are 0 for measure not available.

Note that any derivative work MUST respond to LICENSE command with the same licensing terms.

NOTE for AMB emulation this is an emulationfor AMBRC protocol. Passage records with number of hits and low voltage indicator are supported. This is to use the decoder with lap timing softwares that do not support CANO protocol. Low voltage bit is rised with a voltage threshold set in the decoder configuration

Example:

GET TIME

Response

SUCCESS GET TIME 00075A06

Current time in quarter of ms = 0x00075A06 = 120.449 seconds

To set the same time:

SET TIME 75A06

<font 10pt/-apple-system;rgb(36, 41, 46) font-family: -apple-system; font-size: 10pt;;;inherit>Transponder management</font>/-apple-system;;inherit;;inherit>tx number, for example REGISTER 3462137 The decoder will start learn and return success or failure. In case of failure, reposition the car and/or check correct loop connection. In case of success, the 12 most important 'packets' of the transponder are reported, with the number of hits for each one. A minimum number of hits above 30, with the maximum above 100 is a very good target. The registration can use a nickname for the transponder, like REGISTER 3462137 MARCO. The nick name will appear in the list of registered transponders. The last option is to make a transponder 'important' that is it's never going to be 'kicked out' of the memory if the limit of 40 transponders is reached. Important transponders can be only deleted manually. When the memory is full, the oldest non important transponders are deleted to make room for the last registered one. For example, to register yours as an important transponder, write REGISTER I 3462137 MINE where MINE is the optional nickname. Learn process can be interrupted with the ABORT command, but it will timeout if no transponder is detected. The LIST command will show the registered transponders. The DELETE tx number, for example DELETE 3462137, will remove a transponder registration from the decoder memory. The INFO tx number, will show registration informations for a specific transponder. This commands are made to backup on the computer registration informations. Flashing a new firmware will EREASE the registrations done. </font>

 <font 10pt/-apple-system;rgb(36, 41, 46) font-family: -apple-system; font-size: 10pt;;;inherit>Configuration, beeper and led management</font>"><font inherit"><font inherit/-apple-system;;inherit;;inherit>Command</font>|   \\  <font 10pt/-apple-systemrgb(36, 41, 46) font-family: -apple-system font-size: 10pt;;;inherit>Configuration, beeper and led management</font>/-apple-system;;inherit;;inherit>Description </font>|

NOTE a 50 ms blank time is always inserted in case of multiple close car passages.

DETECT response is multi line. The last line is SUCCESS PIC MODEL NNNN where *<font inherit“>NNNNis Hex part number ID. A value of 3066 sould be reported for PIC 16F18313.

Eingefügt aus <https://github.com/mv4wd/RCHourglass/wiki/CommandReference>